Samsung Refrigerator Error Codes Explained

Samsung refrigerator error codes help identify cooling, defrost, fan, sensor, communication, and control board problems. Use this guide to understand what each error code means, what may have caused it, and what you can safely check before scheduling a repair.

Jamp to Error Code

5E

8E

14E

21E

22E

33E

39E

40E

83E

84C

85C

85E

86E

AP

41/41C

88 88

PC ER

OF OF

Common Samsung Refrigerator Problems We Repair

Our local refrigerator repair technicians are on standby, ready to solve your problem today. We offer same-day refrigerator repair in Ottawa for these issues and more.

🧊 5E — Refrigerator Defrost Sensor Error →

ℹ️ What This Error Means

Samsung refrigerator error code 5E indicates a problem with the refrigerator defrost sensor. This sensor monitors the temperature around the evaporator during the automatic defrost cycle. When the control board receives an abnormal or missing sensor signal, the refrigerator may display the 5E error code.

⚠️ Common Symptoms

Frost forming behind the refrigerator’s interior rear panel
Refrigerator compartment becoming warmer than normal
Cooling performance changing throughout the day
Evaporator fan noise caused by contact with ice
The 5E code returning after the refrigerator is restarted

🔍 Components To Inspect

Refrigerator defrost sensor
Sensor connector
Wiring between the sensor and control board
Evaporator area for excessive frost
Main control board signal circuit

These components should be inspected rather than automatically replaced because the displayed code identifies the monitored circuit, not necessarily the exact failed part.

🛠️ Checks The Homeowner Can Try

Disconnect the refrigerator from power for approximately five minutes.
Restore power and check whether the code returns.
Confirm that the refrigerator doors close completely.
Check whether packages or containers are preventing the door gasket from sealing.
Avoid removing internal panels or testing electrical components without appropriate experience.

A power reset may clear a temporary control error, but it will not repair a damaged sensor, wiring fault, or recurring defrost problem.

🟡 Can You Continue Using the Refrigerator?

Limited use.

The refrigerator may continue operating, but cooling can become inconsistent if the defrost system is not being controlled correctly. Monitor the internal temperature and move perishable food if the fresh-food compartment becomes too warm.

👨‍🔧 Professional Diagnosis

A technician can access the evaporator area, inspect frost accumulation, test the defrost sensor resistance, check the wiring and connectors, and confirm whether the control board is receiving the correct sensor signal. The failed component should only be replaced after testing identifies the cause.

💵 Repair Cost In Ottawa

The final cost depends on the Samsung refrigerator model, accessibility of the evaporator compartment, the component that failed, and the labour required.

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If error code 5E returns after a power reset or the refrigerator is no longer maintaining a safe temperature, YANFIX can diagnose the defrost sensor circuit and determine which component requires repair.

↑ Back to Error Code List

🧊 8E — Ice Maker (Freezer) Sensor Error →

ℹ️ What This Error Means

Samsung refrigerator error code 8E indicates an Ice Maker (Freezer) Sensor Error. The refrigerator has detected an abnormal signal from the ice maker temperature sensor located in the freezer ice maker assembly.

⚠️ Common Symptoms

Ice maker stops producing ice
Ice production becomes inconsistent
Error code 8E remains on the display
Ice maker may not complete the normal ice-making cycle
The error may return after restarting the refrigerator

🔍 Components To Inspect

Ice maker temperature sensor
Ice maker assembly
Sensor connector
Wiring between the sensor and control board

Samsung identifies the monitored component as the ice maker sensor circuit. The displayed error code does not confirm which individual part has failed.

🛠️ Checks The Homeowner Can Try

Verify that the freezer door closes completely.
Disconnect power to the refrigerator for several minutes or switch off the circuit breaker.
Restore power and check whether the error code returns.

If the code continues to appear after the restart, Samsung recommends requesting service.

🟡 Can You Continue Using the Refrigerator?

Limited use.

The refrigerator may continue cooling normally, but the ice maker may not operate correctly while the sensor error is active. If the code remains after restarting the appliance, professional diagnosis is recommended.

👨‍🔧 Professional Diagnosis

A technician will diagnose the ice maker sensor circuit by checking the sensor, wiring, connectors, and related control signals to determine the source of the fault before replacing any components.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the ice maker assembly
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 8E error returns after restarting the refrigerator or your ice maker has stopped producing ice, YANFIX can diagnose the ice maker sensor circuit and identify the component requiring repair.

↑ Back to Error Code List

🧊 14E — Ice Maker Sensor Error→

ℹ️ What This Error Means

Samsung refrigerator error code 14E indicates an Ice Maker Sensor Error. The control board has detected an abnormal signal from the ice maker sensor circuit and cannot correctly monitor the ice maker temperature.

⚠️ Common Symptoms

Ice maker stops producing ice
Ice production becomes irregular
Error code 14E remains on the display
Ice maker may not complete its normal operating cycle
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Ice maker sensor
Ice maker assembly
Sensor connector
Wiring between the sensor and the main control board

The 14E code identifies a fault in the monitored sensor circuit. It does not confirm that the sensor itself has failed. Additional testing is required to identify the defective component.

🛠️ Checks The Homeowner Can Try

Turn the refrigerator off for approximately 10 minutes.
Restore power and check whether the error code returns.
Verify that the ice maker is properly installed and switched on.
If the error immediately returns, further diagnosis is recommended.

🟡 Can You Continue Using the Refrigerator?

Limited use.

The refrigerator will usually continue cooling, but the ice maker may stop operating correctly until the fault is diagnosed and repaired.

👨‍🔧 Professional Diagnosis

A technician will inspect the ice maker sensor circuit, verify sensor readings, check the wiring and connectors, and test the ice maker assembly before determining whether any components require replacement.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the ice maker assembly
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If 14E continues to appear after restarting the refrigerator or your ice maker has stopped producing ice, YANFIX can diagnose the ice maker sensor circuit and determine which component requires repair.

↑ Back to Error Code List

🧊 21E — Freezer Fan Error →

ℹ️ What This Error Means

Samsung refrigerator error code 21E indicates a Freezer Fan Error. The control board is not receiving rotational feedback from the freezer evaporator fan motor when the fan is expected to be operating.

⚠️ Common Symptoms

Freezer cooling performance decreases
Air circulation inside the freezer is reduced
Error code 21E remains on the display
Unusual fan noise or no fan noise at all
The error may return after restarting the refrigerator

🔍 Components To Inspect

Freezer evaporator fan motor
Fan wiring and connectors
Fan blade for ice obstruction
Door gasket
Freezer door alignment

Samsung identifies 21E as a freezer fan error. The code indicates that the control board is not receiving the expected feedback from the fan motor. It does not by itself identify the exact failed component.

🛠️ Checks The Homeowner Can Try

Make sure the freezer door closes completely.
Check that nothing prevents the door from sealing properly.
Inspect the door gasket for gaps or damage.
If ice has formed around the fan area, manually defrost the refrigerator according to Samsung’s recommendations.
If the error returns after defrosting, service is recommended.

🟡 Can You Continue Using the Refrigerator?

Limited use.

The refrigerator may continue operating, but freezer cooling performance can be affected because proper air circulation may not be maintained while the error is active.

👨‍🔧 Professional Diagnosis

A technician will inspect the freezer evaporator fan motor, verify that the fan rotates correctly, check for ice preventing fan movement, inspect the wiring and connectors, and confirm that the control board is receiving the proper feedback signal before replacing any components.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the freezer evaporator
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 21E error continues to appear after defrosting or restarting the refrigerator, YANFIX can diagnose the freezer fan circuit, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 22E — Refrigerator Fan Error→

ℹ️ What This Error Means

Samsung refrigerator error code 22E indicates a Refrigerator Fan Error. The control board is not receiving the expected rotational feedback signal from the refrigerator compartment fan motor while the fan is commanded to operate.

⚠️ Common Symptoms

Fresh food compartment becomes warmer than normal
Weak or no airflow from the refrigerator air vents
Uneven temperatures inside the refrigerator compartment
Error code 22E remains on the display
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Refrigerator evaporator fan motor
Fan blade for ice obstruction
Fan wiring and connectors
Refrigerator evaporator cover
Main control board fan circuit

Samsung identifies 22E as a refrigerator fan error. The displayed code indicates that the fan circuit is not operating as expected, but it does not identify the exact failed component. Further diagnosis is required before replacing any parts.

🛠️ Checks The Homeowner Can Try

Make sure the refrigerator doors close completely.
Check that food packages are not blocking the air vents.
Disconnect power to the refrigerator for several minutes, then restore power.
If excessive frost is visible inside the refrigerator compartment, allow the appliance to fully defrost following Samsung’s recommendations.
If the 22E error returns, professional diagnosis is recommended.

🟡 Can You Continue Using the Refrigerator?

Limited use.

The refrigerator may continue running, but cooling performance in the fresh food compartment may be reduced because proper air circulation cannot be maintained while the fan error is active.

👨‍🔧 Professional Diagnosis

A technician will verify fan motor operation, inspect the fan for ice blockage, test the wiring and connectors, and confirm that the control board is receiving the proper fan feedback signal before determining whether any components require replacement.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the refrigerator evaporator compartment
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 22E error continues to appear after restarting or defrosting the refrigerator, YANFIX can diagnose the refrigerator fan circuit, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 33E — Ice Pipe Heater Error →

ℹ️ What This Error Means

Samsung refrigerator error code 33E indicates an Ice Pipe Heater Error. The control board has detected a problem with the ice pipe heater circuit. This heater helps prevent the water fill tube supplying the ice maker from freezing during normal operation.

⚠️ Common Symptoms

Ice maker stops producing ice
Water may not reach the ice maker
Error code 33E remains on the display
Ice production becomes intermittent or stops completely
The error may return after restarting the refrigerator

🔍 Components To Inspect

Ice pipe heater
Ice pipe heater wiring
Electrical connectors
Main control board heater circuit

Samsung identifies 33E as an Ice Pipe Heater Error. The displayed code indicates a fault in the monitored heater circuit but does not identify the exact failed component. Additional diagnosis is required before replacing any parts.

🛠️ Checks The Homeowner Can Try

Disconnect power to the refrigerator for several minutes.
Restore power and check whether the error code returns.
Verify that the freezer door closes completely.
If the 33E error returns, professional diagnosis is recommended.

Samsung does not provide homeowner troubleshooting procedures for testing the ice pipe heater or its electrical circuit.

🟡 Can You Continue Using the Refrigerator?

Limited use.

The refrigerator will usually continue cooling normally, but the ice maker may not operate correctly while the ice pipe heater error is active.

👨‍🔧 Professional Diagnosis

A technician will inspect the ice pipe heater circuit, verify heater continuity, check the wiring and connectors, and confirm that the control board is supplying and monitoring the heater circuit correctly before determining which component requires repair.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the ice maker assembly
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 33E error remains after restarting the refrigerator or your ice maker has stopped working properly, YANFIX can diagnose the ice pipe heater circuit, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 39E — Ice Maker Function Error→

ℹ️ What This Error Means

Samsung refrigerator error code 39E indicates an Ice Maker Function Error. The control board has detected an abnormal condition in the ice maker system and cannot complete the normal ice-making operation.

⚠️ Common Symptoms

Ice maker stops producing ice
Ice production becomes irregular
Error code 39E remains on the display
The ice maker may fail to complete its operating cycle
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Ice maker assembly
Ice maker wiring
Electrical connectors
Main control board communication with the ice maker

Samsung identifies 39E as an Ice Maker Function Error. The displayed code indicates a fault within the monitored ice maker system but does not identify the exact failed component. Additional diagnosis is required before replacing any parts.

🛠️ Checks The Homeowner Can Try

Turn the refrigerator off for several minutes.
Restore power and check whether the error code returns.
Verify that the freezer door closes completely.
If equipped, ensure the ice maker is turned on.
If the 39E error returns, professional diagnosis is recommended.

Samsung does not publish homeowner diagnostic procedures for testing the internal ice maker components associated with this error.

🟡 Can You Continue Using the Refrigerator?

Yes, with limited functionality.

The refrigerator will usually continue cooling normally, but the automatic ice maker may stop operating until the fault has been diagnosed and repaired.

👨‍🔧 Professional Diagnosis

A technician will diagnose the ice maker system, inspect the wiring and connectors, verify communication between the ice maker and the control board, and determine which component is responsible for the error before replacing any parts.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the ice maker assembly
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 39E error continues to appear after restarting the refrigerator or your ice maker is no longer functioning correctly, YANFIX can diagnose the ice maker system, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 40E — Ice Room Fan Error →

ℹ️ What This Error Means

Samsung refrigerator error code 40E indicates an Ice Room Fan Error. The control board is not receiving the expected operating feedback from the fan motor located in the ice room compartment.

⚠️ Common Symptoms

Ice maker stops producing ice
Reduced airflow inside the ice room
Error code 40E remains on the display
Ice production becomes slow or stops completely
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Ice room fan motor
Fan blade for ice obstruction
Fan wiring
Electrical connectors
Main control board fan circuit

Samsung identifies 40E as an Ice Room Fan Error. The displayed code indicates a fault in the monitored fan circuit but does not identify the exact failed component. Further diagnosis is required before replacing any parts.

🛠️ Checks The Homeowner Can Try

Turn the refrigerator off for several minutes.
Restore power and check whether the error code returns.
Verify that the freezer door closes completely.
If excessive ice is visible around the ice maker compartment, follow Samsung’s recommended defrost procedure.
If the 40E error returns, professional diagnosis is recommended.

Samsung does not publish homeowner procedures for testing the ice room fan motor or its electrical circuit.

🟡 Can You Continue Using the Refrigerator?

Limited use.

The refrigerator will usually continue cooling normally, but the ice maker may not function correctly while the ice room fan error is active.

👨‍🔧 Professional Diagnosis

A technician will inspect the ice room fan motor, check for ice preventing fan rotation, verify the wiring and connectors, and confirm that the control board is receiving the proper fan feedback signal before determining which component requires repair.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the ice room compartment
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 40E error continues to appear after restarting the refrigerator or your ice maker is no longer operating properly, YANFIX can diagnose the ice room fan circuit, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 83E — Compressor Abnormal Current Error→

ℹ️ What This Error Means

Samsung refrigerator error code 83E indicates a Compressor Abnormal Current Error. The refrigerator has detected an abnormal current condition in the inverter compressor circuit and has stopped normal operation to protect the system.

⚠️ Common Symptoms

Refrigerator stops cooling
Compressor may not start
Error code 83E remains on the display
The refrigerator may restart repeatedly without cooling
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Inverter compressor
Inverter PCB
Compressor wiring harness
Electrical connectors
Main control board communication

Samsung identifies 83E as a Compressor Abnormal Current Error. The displayed code indicates that an abnormal current condition has been detected in the compressor circuit, but it does not identify the exact failed component. Professional diagnosis is required before replacing any parts.

🛠️ Checks The Homeowner Can Try

Disconnect the refrigerator from power for several minutes.
Restore power and check whether the error code returns.
Verify that the refrigerator is connected to a stable power supply.
If the 83E error returns, Samsung recommends professional service.

Samsung does not publish homeowner diagnostic procedures for testing the inverter compressor or inverter PCB.

🔴 Can You Continue Using the Refrigerator?

No.

A refrigerator displaying the 83E error may not cool properly because the compressor protection system has detected an abnormal operating condition. Food safety may be affected if cooling cannot be maintained.

👨‍🔧 Professional Diagnosis

A technician will inspect the inverter compressor circuit, verify electrical connections, test the inverter PCB, and confirm whether the compressor is operating within normal electrical specifications before determining which component requires repair or replacement.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the compressor compartment
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 83E error remains after restarting the refrigerator or the appliance has stopped cooling, YANFIX can diagnose the inverter compressor circuit, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 84C — Compressor Lock Error →

ℹ️ What This Error Means

Samsung refrigerator error code 84C indicates a Compressor Lock Error. The control board has detected that the inverter compressor failed to start or could not continue operating as expected after a start attempt.

⚠️ Common Symptoms

Refrigerator stops cooling
Compressor does not appear to start
Error code 84C remains on the display
The refrigerator may repeatedly attempt to restart the compressor
The error may return after power is restored

🔍 Components To Inspect

Inverter compressor
Inverter PCB
Compressor wiring harness
Electrical connectors
Main control board communication

Samsung identifies 84C as a Compressor Lock Error. The error indicates that the compressor failed to operate normally, but it does not identify which component has failed. Additional diagnosis is required before replacing any parts.

🛠️ Checks The Homeowner Can Try

Disconnect the refrigerator from power for several minutes.
Restore power and check whether the error code returns.
Verify that the refrigerator is connected to a stable electrical supply.
If the 84C error returns, Samsung recommends professional service.

Samsung does not provide homeowner diagnostic procedures for testing the inverter compressor or inverter control board.

🔴 Can You Continue Using the Refrigerator?

No.

The refrigerator may not maintain safe food storage temperatures because the compressor is not operating normally. If cooling has stopped, food safety may be affected.

👨‍🔧 Professional Diagnosis

A technician will inspect the inverter compressor circuit, verify electrical connections, test the inverter control board, and confirm whether the compressor can start and operate correctly before determining which component requires repair.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the compressor compartment
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 84C error remains after restarting the refrigerator or the appliance has stopped cooling, YANFIX can diagnose the inverter compressor system, identify the cause of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 85C — Compressor Under Voltage Error→

ℹ️ What This Error Means

Samsung refrigerator error code 85C indicates a Compressor Under Voltage Error. The control board has detected that the inverter compressor is receiving a supply voltage below the required operating range. To protect the compressor, normal operation may be interrupted.

⚠️ Common Symptoms

Refrigerator stops cooling
Compressor may not start or may stop unexpectedly
Error code 85C remains on the display
Cooling performance is reduced or completely lost
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Household power supply
Power cord and electrical connections
Inverter PCB
Inverter compressor
Wiring harness and electrical connectors

Samsung identifies 85C as a Compressor Under Voltage Error. The error indicates that an undervoltage condition has been detected but does not identify which component is responsible. Professional diagnosis is required to determine the cause.

🛠️ Checks The Homeowner Can Try

Disconnect the refrigerator from power for several minutes.
Restore power and check whether the error code returns.
Verify that the refrigerator is plugged directly into a properly grounded wall outlet.
Avoid using extension cords or power strips.
If the 85C error returns, Samsung recommends professional service.

Samsung does not provide homeowner procedures for testing the inverter compressor, inverter PCB, or internal electrical circuits.

🔴 Can You Continue Using the Refrigerator?

No.

An undervoltage condition may prevent the compressor from operating correctly, causing the refrigerator to lose cooling performance. If the appliance is no longer maintaining safe temperatures, food may spoil.

👨‍🔧 Professional Diagnosis

A technician will verify the incoming supply voltage, inspect the inverter compressor circuit, test the inverter PCB, check the wiring and connectors, and determine the source of the undervoltage condition before replacing any components.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
The source of the undervoltage condition
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 85C error remains after restarting the refrigerator or the appliance has stopped cooling, YANFIX can diagnose the inverter compressor system, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 85E — Compressor Over Current Error →

ℹ️ What This Error Means

Samsung refrigerator error code 85E indicates a Compressor Over Current Error. The control board has detected that the inverter compressor is drawing more current than expected during operation. To protect the refrigeration system, the compressor may be stopped.

⚠️ Common Symptoms

Refrigerator stops cooling
Compressor may fail to start or shut down shortly after starting
Error code 85E remains on the display
Cooling performance is reduced or completely lost
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Inverter compressor
Inverter PCB
Compressor wiring harness
Electrical connectors
Main control board communication

Samsung identifies 85E as a Compressor Over Current Error. The displayed error indicates that an overcurrent condition has been detected in the compressor circuit but does not identify which component has failed. Professional diagnosis is required before replacing any parts.

🛠️ Checks The Homeowner Can Try

Disconnect the refrigerator from power for several minutes.
Restore power and check whether the error code returns.
Verify that the refrigerator is connected directly to a properly grounded wall outlet.
If the 85E error returns, Samsung recommends professional service.

Samsung does not publish homeowner diagnostic procedures for testing the inverter compressor or inverter control board.

🔴 Can You Continue Using the Refrigerator?

No.

If the compressor is unable to operate because an overcurrent condition has been detected, the refrigerator may not maintain safe food storage temperatures.

👨‍🔧 Professional Diagnosis

A technician will inspect the inverter compressor circuit, verify the compressor’s operating current, test the inverter PCB, inspect the wiring and electrical connections, and determine the source of the overcurrent condition before replacing any components.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the compressor compartment
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 85E error remains after restarting the refrigerator or the appliance has stopped cooling, YANFIX can diagnose the inverter compressor system, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🧊 86E — Compressor Over Voltage Error→

ℹ️ What This Error Means

Samsung refrigerator error code 86E indicates a Compressor Over Voltage Error. The refrigerator has detected an overvoltage condition affecting the inverter compressor circuit. This can occur following a power surge or another electrical anomaly.

⚠️ Common Symptoms

Error code 86E remains on the display
Refrigerator may stop cooling
Compressor may not start normally
The error may appear after a power surge or electrical disturbance
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Household power supply
Inverter compressor
Inverter PCB
Compressor wiring harness
Electrical connectors

Samsung identifies 86E as a Compressor Over Voltage Error. The code confirms that an overvoltage condition has been detected but does not identify the failed component. Professional diagnosis is required to determine the cause.

🛠️ Checks The Homeowner Can Try

Turn the refrigerator off by unplugging it or switching off the circuit breaker.
Leave the power off for approximately 60 seconds.
Restore power and check whether the error code clears.
If the 86E error returns, Samsung recommends requesting service.

Samsung does not publish homeowner diagnostic procedures for testing the inverter compressor or inverter control board.

🔴 Can You Continue Using the Refrigerator?

No.

If the 86E error remains active, the refrigerator may not cool correctly because the compressor protection system has detected an abnormal electrical condition. Food safety may be affected if proper temperatures cannot be maintained.

👨‍🔧 Professional Diagnosis

A technician will verify the incoming power supply, inspect the inverter compressor circuit, test the inverter PCB, check the wiring and electrical connections, and determine the source of the overvoltage condition before replacing any components. This reflects the diagnostic process; Samsung does not identify a specific failed part for this error.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
The source of the electrical fault
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 86E error returns after restoring power or your refrigerator has stopped cooling, YANFIX can diagnose the inverter compressor system, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

📶 AP — Access Point Mode→

ℹ️ What This Means

AP is not an error code. It stands for Access Point Mode.

The refrigerator enters this mode when it is acting as a wireless access point so it can be connected to the SmartThings app during Wi-Fi setup. AP may appear after manually starting the Wi-Fi pairing process.

⚠️ What You May Notice

AP is displayed on the control panel.
The refrigerator continues to cool normally.
Wi-Fi setup or SmartThings connection is in progress.
The display returns to normal after setup is completed or the setup session times out.

🔍 What To Check

Confirm whether you recently started the SmartThings setup.
Check if someone accidentally activated Wi-Fi pairing mode.
Verify that the SmartThings connection process has finished.

🛠️ What The Homeowner Can Do

Complete the SmartThings setup if you are connecting the refrigerator to Wi-Fi.
If you entered AP mode by mistake, wait for it to exit automatically or follow your refrigerator model’s instructions to leave AP mode.
No repair is required unless another error code appears.

🟢 Can You Continue Using the Refrigerator?

Yes.

AP is not a fault. It is a normal operating mode used only for Wi-Fi configuration. Cooling operation is not affected by AP mode itself.

👨‍🔧 Professional Diagnosis

Professional service is not normally required for AP mode. If the refrigerator cannot connect to Wi-Fi or repeatedly enters AP mode unexpectedly, a technician can inspect the network configuration and related electronic components after basic setup has been ruled out.

💵 Service In Ottawa

If your Samsung refrigerator displays AP together with other error codes, experiences Wi-Fi connection problems that cannot be resolved, or is not operating normally, YANFIX can diagnose the issue and determine whether service is required.

Service Call From $80

🔗 Related Topics

📞 Need Samsung Refrigerator Repair In Ottawa?

If your refrigerator remains in AP mode unexpectedly or displays additional error codes, YANFIX can diagnose the problem and determine whether the issue is related to the Wi-Fi configuration or another refrigerator system.

↑ Back to Error Code List

📶 41 / 41C — Communication Error→

ℹ️ What This Error Means

Samsung refrigerator code 41 or 41C indicates a Communication Error. The refrigerator has detected a communication problem between the main control board and another electronic module. On Family Hub models, this commonly refers to a communication issue between the Family Hub display and the refrigerator’s main control system.

⚠️ Common Symptoms

Error code 41 or 41C appears on the display
Family Hub screen may not function correctly (on applicable models)
Smart features may become unavailable
The refrigerator may continue cooling normally
The error may return after the refrigerator is restarted

🔍 Components To Inspect

Communication wiring harness
Electrical connectors
Main control board
Family Hub display module (Family Hub models)
Communication circuit

Samsung identifies 41 / 41C as a Communication Error. The code indicates that communication between electronic modules has been interrupted but does not identify the exact failed component. Professional diagnosis is required.

🛠️ Checks The Homeowner Can Try

Disconnect the refrigerator from power for several minutes.
Restore power and check whether the error code clears.
If your refrigerator is connected to Wi-Fi, verify that SmartThings and the Family Hub functions operate normally.
If the 41 or 41C error returns, Samsung recommends requesting service.

Samsung does not provide homeowner diagnostic procedures for testing the internal communication circuits.

🟡 Can You Continue Using the Refrigerator?

Usually, yes.

In many cases, the refrigerator will continue cooling normally while the communication error affects only electronic communication or smart features. However, if cooling performance is also affected or additional error codes appear, professional diagnosis is recommended.

👨‍🔧 Professional Diagnosis

A technician will inspect the communication wiring, verify the electrical connections, test communication between the electronic modules, and determine which component is responsible for the communication failure before replacing any parts.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
The electronic module affected
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 41 or 41C error remains after restarting the refrigerator or additional problems have appeared, YANFIX can diagnose the communication system, identify the source of the fault, and recommend the appropriate repair.

↑ Back to Error Code List

⚠️ 88 88 — Power Interruption Error→

ℹ️ What This Error Means

Samsung refrigerator code 88 88 indicates that the refrigerator has detected a power interruption or has just been restored after a loss of electrical power. This is not a component failure. The code is displayed after the control system restarts and performs its normal initialization.

⚠️ Common Symptoms

88 88 appears immediately after power is restored
The refrigerator has recently been unplugged or the circuit breaker was turned off
A household power outage has occurred
The refrigerator may continue cooling normally after startup
The display returns to normal after initialization or user confirmation

🔍 What To Check

Verify that household power has been restored.
Confirm that the refrigerator is plugged into a properly grounded wall outlet.
Check whether the circuit breaker has tripped.
If 88 88 remains on the display after power has been restored, further diagnosis may be required.

Samsung identifies 88 88 as a condition related to power interruption, not as a failure of a specific refrigerator component.

🛠️ Checks The Homeowner Can Try

Confirm that electrical power has been fully restored.
Press any button on the control panel to clear the display (if supported by your model).
Allow the refrigerator to complete its startup process.
If the code does not clear or returns without another power interruption, Samsung recommends requesting service.

🟢 Can You Continue Using the Refrigerator?

Yes.

In most cases, 88 88 is not an error requiring repair. If the display clears and the refrigerator resumes normal cooling, no service is necessary.

👨‍🔧 Professional Diagnosis

If 88 88 remains on the display after power has been restored or appears repeatedly without a power outage, a technician can inspect the incoming power supply, electrical connections, and electronic control system to determine whether another fault is present.

💵 Service In Ottawa

If 88 88 does not clear after the refrigerator restarts or your refrigerator is no longer cooling properly, YANFIX can diagnose the electrical system and determine whether additional repairs are required.

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the 88 88 code remains on the display after power has been restored or your refrigerator is not operating normally, YANFIX can identify the cause of the problem and recommend the appropriate repair.

↑ Back to Error Code List

🔌 PC ER — Door Communication Error→

ℹ️ What This Error Means

Samsung refrigerator code PC ER (also displayed as PC-ER, PC ER, or PC CH on some models) indicates a communication error between the main control board and the door electronic components. This error commonly occurs after the refrigerator doors have been removed and reinstalled or when the door communication connector is not fully connected.

⚠️ Common Symptoms

PC ER appears on the display.
The refrigerator may continue cooling normally.
The display or dispenser functions may not operate correctly.
The error often appears immediately after the refrigerator doors have been removed or reinstalled.
The error remains until the communication problem is corrected.

🔍 Components To Inspect

Door communication connector
Wiring harness between the cabinet and the refrigerator door
Electrical connectors
Main control board communication circuit

Samsung identifies PC ER as a communication error. The code indicates that communication between the refrigerator cabinet and the door electronics has been interrupted. It does not identify a failed component.

🛠️ Checks The Homeowner Can Try

Verify that both refrigerator doors are fully closed.
If the doors were recently removed, inspect the communication connector at the top door hinge and ensure it is fully seated.
Disconnect power to the refrigerator for several minutes.
Restore power and check whether the error clears.
If the PC ER code remains, Samsung recommends professional service.

Samsung specifically notes that this error commonly occurs when the door communication connector has not been reconnected correctly after door installation.

🟡 Can You Continue Using the Refrigerator?

Usually, yes.

The refrigerator may continue cooling normally, but certain door-mounted electronic functions, such as the dispenser or display (depending on the model), may not operate correctly until communication is restored.

👨‍🔧 Professional Diagnosis

A technician will inspect the door communication harness, verify connector alignment, test the communication circuit, and confirm proper communication between the main control board and the door electronics before determining whether any components require repair.

💵 Repair Cost In Ottawa

The final repair cost depends on:

Samsung refrigerator model
Accessibility of the door wiring and connectors
The component identified during diagnosis
Labour required

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If the PC ER code remains after reconnecting the door wiring or restarting the refrigerator, YANFIX can diagnose the communication system, identify the source of the problem, and recommend the appropriate repair.

↑ Back to Error Code List

🏪 OF OF — Cooling Off Mode (Demo Mode)→

ℹ️ What This Means

OF OF (sometimes displayed as OF, O FF, or OFF) indicates that the refrigerator is operating in Cooling Off Mode, also known as Demo Mode. This mode is designed for showroom displays and disables the refrigeration system while allowing the lights, display, and other electronic features to continue operating normally.

⚠️ Common Symptoms

OF OF appears on the display.
The refrigerator and freezer do not cool.
Interior lights operate normally.
The display and control panel continue to function.
The compressor does not run.

🔍 What To Check

Verify whether Cooling Off Mode was accidentally activated.
Check whether the refrigerator was recently delivered, moved, or placed on display.
Confirm that the refrigerator is not intentionally set to Demo Mode.

Samsung identifies OF OF as Cooling Off Mode, not as a system fault or component failure.

🛠️ Checks The Homeowner Can Try

Exit Cooling Off Mode using the button combination specified for your refrigerator model.
Allow several hours for the refrigerator to return to normal operating temperature after cooling resumes.
If OF OF cannot be cleared using the correct procedure, Samsung recommends requesting service.

The method for turning Cooling Off Mode on or off varies by refrigerator model.

🟢 Can You Continue Using the Refrigerator?

No, if food needs to be kept cold.

While OF OF is active, the refrigerator does not cool. This mode is intended only for showroom display and should not be used for food storage.

👨‍🔧 Professional Diagnosis

Professional service is usually not required if the refrigerator is simply in Cooling Off Mode. If the display continues to show OF OF after the correct procedure has been used to exit Demo Mode, a technician can diagnose the control system and determine whether another fault is present.

💵 Service In Ottawa

If you cannot exit Cooling Off Mode or your refrigerator still does not cool after returning to normal operation, YANFIX can diagnose the control system and determine whether additional repairs are required.

Service Call From $80

🔗 Related Refrigerator Problems

📞 Need Samsung Refrigerator Repair In Ottawa?

If your Samsung refrigerator continues to display OF OF or still does not cool after exiting Cooling Off Mode, YANFIX can diagnose the problem and recommend the appropriate repair.

↑ Back to Error Code List

How We Diagnose Refrigerator Error Codes

1

Read the Error Code

2

Perform Electrical Testing

3

Verify the Failed Component

4

Complete the Repair

5

Clear Error Code

6

Run Full Test Cycle

Common Parts We Replace

Evaporator Fan Motor

Defrost Heater

Defrost Thermostat

Thermistor Sensor

Ice Maker Assembly

Water Inlet Valve

Main Control Board

Inverter Board

RELATED REFRIGERATOR REPAIR SERVICE

A refrigerator that is running but not cooling properly may have airflow restrictions, evaporator fan problems, sensor failures, control board issues, or compressor-related faults. Learn more about diagnosing and repairing refrigerator cooling problems.

Water leaks inside the refrigerator or on the kitchen floor are often caused by clogged defrost drains, damaged water lines, blocked drain tubes, or ice maker system failures. Explore common causes and repair solutions.

Ice makers may stop producing ice because of water supply problems, frozen fill tubes, faulty valves, sensor failures, or defective ice maker assemblies. Learn how common ice maker problems are diagnosed and repaired.

Buzzing, rattling, clicking, humming, or grinding sounds can indicate fan motor failures, airflow problems, compressor issues, or worn mechanical components. Find out what causes unusual refrigerator noises.

A freezer that is running but not freezing properly may have compressor problems, evaporator fan failures, refrigerant leaks, frost buildup, temperature sensor issues, or control board faults. Learn the most common causes of poor freezing performance and how professional diagnosis identifies the failed component before repair.

Explore all refrigerator repair services provided by YANFIX throughout Ottawa, including cooling problems, leaks, ice maker repairs, temperature control issues, frost buildup, and electronic system diagnostics.

You’ve Got Questions?
We’ve Got Answers!

Everything you need to know before you book.

What does a refrigerator error code mean?

A refrigerator error code is a diagnostic message generated by the appliance’s electronic control system. Instead of identifying the exact failed part, the code points to the system where a problem has been detected, such as cooling, defrost, fan operation, temperature sensing, ice maker components, or communication between control boards. Professional testing is usually required to identify the exact cause before replacing any parts.

Can I reset a refrigerator error code myself?

Some refrigerator error codes disappear automatically after the underlying problem has been corrected or after a power reset. However, if the fault remains, the code will usually return within a short period. Resetting the display without diagnosing the actual problem will not repair the refrigerator or prevent additional damage.

Why does the same refrigerator error code keep coming back?

A recurring error code usually indicates that the original fault has not been repaired. Common causes include defective thermistors, failed defrost heaters, faulty evaporator fan motors, damaged wiring, malfunctioning control boards, or compressor-related problems. Accurate electrical testing is necessary before replacing components.

Are refrigerator error codes the same for every brand?

No. Each manufacturer uses its own diagnostic system and code definitions. For example, Samsung, LG, Whirlpool, Frigidaire, GE, Bosch, KitchenAid, and Maytag refrigerators all display different error codes, even when the underlying problem is similar. Always interpret the code according to the specific refrigerator brand and model.

Is it safe to continue using a refrigerator with an error code?

If you decide not to proceed with the repair, a small service call fee will apply.
This fee covers the technician’s time and on-site diagnostics. However, if you go ahead with the repair — the service call is absolutely free.

Do you diagnose refrigerator error codes for all major brands?

Yes. YANFIX diagnoses refrigerator error codes for all major refrigerator brands throughout Ottawa, including Samsung, LG, Whirlpool, GE, Frigidaire, Bosch, KitchenAid, Maytag, and many others. We identify the failed component, explain the cause of the error, and recommend the appropriate repair based on professional diagnostic testing.

Contact Information

Book your same-day Refrigerator & Freezer repair in Ottawa now – we’ll respond within 15 minutes.

18 Inwood Drive Kanata, Ontario, K2M 1Z5
+1613913-30-23
support@yanfix.com
Facebook
Instagram